Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent JennAir specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 766-5788 Request a Technician
Error code · Wall Oven

JennAir Combination Oven Message “Door in Microwave Display”: control waiting for a door open and close

On JennAir built-in wall ovens that include a microwave, with a microwave section, this message means the control is waiting for input from the door switches. It wants to see the door open and then close.…

Low risk · DIY check OK
Request a Technician(713) 766-5788
Code
Door in Microwave Display
Appliance
Wall Oven
Brand
JennAir
Warranty
30-day workmanship

What Door in Microwave Display means

On JennAir built-in wall ovens that include a microwave, with a microwave section, this message means the control is waiting for input from the door switches. It wants to see the door open and then close. You will see the words on the screen when you try to start a microwave function, and the cycle will not begin until the door action registers.

Common causes of Door in Microwave Display

  • Door not fully closed or not opened first before starting
  • Something resting in the door seal area, such as a dish edge or a towel
  • Door switch that does not register the open and close movement
✓ One safe check you can try

1. Open the microwave door all the way. 2. Check the door edge and the frame for crumbs, foil or a dish rim. 3. Close the door firmly until it latches. 4. Start the function again within a few seconds. 5. Call us if Door in Microwave Display is still on the display, and mention the microwave door input.

! Why to stop there
  • The door switches decide whether the microwave is allowed to run, so we do not bypass or adjust them.
  • A switch that fails to register needs a proper meter check, which is not safe to try on a live oven.
  • Using the microwave with a door that does not seal correctly is not something we want you to risk.
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Wall Oven codes

Probe or Insert ProbeJennAir Wall Oven Display Probe or Insert Probe: Meat probe needed PUSH or PSHJennAir Wall Oven Display PUSH or PSH: Press start Sabbath, Sab, 5Ab, or 5A7JennAir Wall Oven Display Sabbath, Sab, 5Ab or 5A7: Sabbath mode is on FC E6JennAir Wall Oven Code FC E6: Wi-Fi power module FC E7JennAir Wall Oven Code FC E7: Oven did not connect to router FC E8JennAir Wall Oven Code FC E8: Registration error FC E9JennAir Wall Oven Code FC E9: Wi-Fi power module wiring Feature Not AvailableJennAir Wall Oven Message "Feature Not Available": Follow the Prompt on the Display
Door in Microwave DisplayDoor in Microwave Display questions
What does the microwave door message ask me to do?

It asks you to open the door and then close it so the control can see both switch states. Usually one deliberate open and shut clears it.

Why does it keep returning after I close the door?

If the door closes but the message persists, a switch may not be registering. A dish rim in the seal area can also be the reason, so clear the edge before testing again.

Does this affect the regular oven side?

The message is tied to the microwave door input. The conventional oven cavity may keep working, but a switch that never registers should still be checked. We give a written price before any work.

Book a visit

Still unsure about Door in Microwave Display?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 766-5788
☎ Call the desk ▤ Request a Technician