Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent JennAir specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 766-5788 Request a Technician
Error code · Refrigerator

JennAir Built-In Column “Replace Filter” Icon: Water Filter Is Overdue

On JennAir built-in column refrigerators such as the JBRFL24IGX or JBRFL30IGX, the Replace Filter icon flashes the whole time water is dispensing. After 14 days without a filter replacement, the icon also blinks seven times and…

Low risk · DIY check OK
Request a Technician(713) 766-5788
Code
Replace Filter
Appliance
Refrigerator
Brand
JennAir
Warranty
30-day workmanship

What Replace Filter means

On JennAir built-in column refrigerators such as the JBRFL24IGX or JBRFL30IGX, the Replace Filter icon flashes the whole time water is dispensing. After 14 days without a filter replacement, the icon also blinks seven times and a tone sounds three times when dispensing ends. JennAir recommends an everydrop water filter. A new filter also needs its status reset afterward, as the owner's manual describes.

Common causes of Replace Filter

  • The water filter is past its replacement interval
  • A new filter was installed but the filter status was never reset
  • The filter is not fully seated
  • A non-matching filter in the holder
✓ One safe check you can try

1. Install a new everydrop water filter and turn it fully into place. 2. Reset the filter status following the owner's manual for your column model. 3. Dispense a few glasses of water to flush air out of the line. 4. Watch the icon during the next dispense to confirm it no longer flashes.

! Why to stop there
  • The reminder comes from the filter status, so a repair visit will not clear it faster than a new filter and a reset.
  • Filters cost much less than a service call.
  • If the icon returns right after a proper change and reset, then the control deserves a look, and we price it in writing.
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Refrigerator codes

POJennAir Built-In Refrigerator Code PO: Power Outage Warmed the Freezer Temperature AlarmJennAir Built-In Column Over-Temp Alarm: Temperatures Stayed Too High Air Filter IndicatorJennAir French-Door Refrigerator Air Filter Indicator: Reset After a New Filter Call for ServiceJennAir Built-In Refrigerator "Call for Service" Light: Reset Power First CL or LOJennAir Beverage Center Code CL or LO: Internal Temperature Too Low Cooling OffJennAir French-Door Refrigerator "Cooling Off" Display: Cooling Turned Off Door AlarmJennAir Built-In Refrigerator Door Alarm: Door or Drawer Left Open Flashing "F"JennAir Built-In Refrigerator Flashing "F": Reset, Then Call If It Stays
Replace FilterReplace Filter questions
Why does the icon flash only while I dispense water?

It is built to remind you when you are using the dispenser. After 14 days without a change, it also blinks seven times and a tone sounds three times at the end of dispensing.

Which filter should I use?

JennAir recommends the everydrop water filter. A different filter may not seat or flow correctly, so choose the one that matches your column and turn it fully into place.

I replaced the filter and the icon still flashes. What now?

Reset the filter status as your owner's manual describes for your model, then dispense again. If it still flashes after that, call us and we will check the control before quoting a price.

Book a visit

Still unsure about Replace Filter?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 766-5788
☎ Call the desk ▤ Request a Technician